Landoll CPP7-03 through CPP12-03 Chisel Plow Manual de usuario

®175rev1113

2-2 7D525ASSEMBLYFrame Assembly Dimensions“Left” and “Right” refer to directions seen as if standing behind the machine and facing in the direction of

ASSEMBLY2-3MastFigure 2-2: MastThe rigid mounted shanks are shipped assembled to the shank clamps. To mount these on the chisel plow, remove the 3/4”

2-4 7D525ASSEMBLYFigure 2-3: Rigid and Spring ClampSpring CushionShank ClampRigid ShankClamp5/8 x 3” Bolts,Nuts, and Lockwashers1”

ASSEMBLY2-5Assembly of Chisel PlowsAfter the basic 7 foot frame is assembled for the 9 foot and 11 foot or the basic 10 foot frame for the 12 foot mod

2-6 7D525ASSEMBLYTo make 9 foot and 12 foot machines the one foot extension is assembled to the basic 7 foot or 10 foot machine. See Figure 2-5. On th

ASSEMBLY2-7Twisted ShovelsIf twisted shovels are to be used, it is suggested that they be arranged on the shanks as shown in Figure 2-7. (L.H. means t

2-8 7D525ASSEMBLYLED Warning LightsFigure 2-8: LED Warning LightsAmber LED LampLED WarningLights HarnessFlasher ControlModule7Pin/4PinWP HarnessRed LE

ASSEMBLY2-9Figure 2-9: Electrical Installation Dimensions17 1/2"(11 Shank)17 1/2"(11 Shank) 4" 17" CLFront View11 Shank Machine S

2-10 7D525ASSEMBLYFigure 2-10: 7’ and 9’ LED Warning Lights LayoutCPP7&9 ElectLayoutSMVAmberLEDRedLEDBolt,1/4-20 x 1-1/2Nut,1/4-207 Pin HarnessU-B

ASSEMBLY2-11Figure 2-11: 10’ and 12’ LED Warning Lights LayoutNut,1/4-207 Pin HarnessLampHarnessLightBracketBolt,1/4-20 x 1-1/2Nut,1/2-13RedLEDAmberLE

2-12 7D525ASSEMBLYFigure 2-12: 11’ LED Warning Lights LayoutCPP11 ElectLayoutSMVSMV MountBolt,5/16-18 x 1Flat Washer,5/16Nut,3/8-16Nut,5/16-18U-Bolt,3

ASSEMBLY2-13LED Installation InstructionsNOTEAll models similar. Refer to Figure 2-9 for bracket and light placement.1. Attach the 2 (two) Light Brack

2-14 7D525ASSEMBLYTable provided for general use.NOTES:

3-1Chapter 3OperationNOTEThis chapter will cover the basic operation and procedures for the Landoll Brillion Chisel Plow. Be sure to read and understa

3-2 7D525OPERATIONTable provided for general use.NOTES:

4-1Chapter 4MaintenanceGeneral Torque Specifications (rev. 4/97)TORQUE SPECIFIED IN FOOT POUNDS This chart provides tightening torques for genera

4-2 7D525MAINTENANCEFastenersBefore operating your Brillion machine, check all hardware for tightness. Use the Tightening Torque Table below as a guid

5-1Chapter 5General Reference and SpecificationsGeneralShanks...1” x 2” x 26” Clearance

5-2 7D525GENERAL REFERENCE AND SPECIFICATIONSTable provided for general use.NOTES:

Document Control Revision Log:Date Revision Improvement(s) Description and Comments07/2001 Initial Release11/2013 175rev1113 Updated to the Landoll fo

7D525 iTable of Contents1 Introduction and Safety InformationIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities.Chise

1-1Chapter 1Introduction and Safety InformationIntroductionThe implement described in this manual has been designed with care and built by skilled wor

1-2 7D525INTRODUCTION AND SAFETY INFORMATIONSafetyNOTEInvestigation has shown that nearly 1/3 of all farm accidents are caused by careless use of mach

INTRODUCTION AND SAFETY INFORMATION1-3Maintenance Safety• Block the implement so it will not roll when working on or under it to prevent injury. • Do

1-4 7D525INTRODUCTION AND SAFETY INFORMATIONDecalsFigure 1-2: Decals and Locations528933528934CAUTION1. DO NOT LUBRICATE, ADJUST OR REPAIR WHEN MA

2-1Chapter 2AssemblyCAUTIONMain Frame Assembly1. Assemble the 7D456 mast assembly and 7D462 plate to the main frame using the 5/8 x 6” bolts, nuts an